COLOUR VIDEO CAMERA
TK-C1430
INSTRUCTIONS
TK-C1431
CAMERA
VIDEO
COLOR
LOOK
BF
DIGITAL
® is a registered trademark owned by Victor Company of Japan, Limited.
® is a registered trademark in Japan, the U.S.A., the U.K. and many other countries.
© 2005 Victor Company of Japan, Limited.
Printed in Thailand
LWT0276-001A-H
LWT0276-001A-H
E-
Thank you for purchasing this product.
Safety Precautions
(These instructions are for TK-C1430E and TK-C1431EG)
Before beginning to operate this unit, please read the instruction manual
carefully in order to make sure that the best possible performance is obtained.
Due to design modifications, data given in this
instruction book are subject to possible change
without prior notice.
CONTENTS
WARNING:
INTRODUCTION
TO REDUCETHE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT
EXPOSETHIS APPLIANCETO RAIN
OR MOISTURE.
Features ...............................................................................................................................6
Operating Precautions .........................................................................................................7
Controls, Connectors and Indicators ...................................................................................8
CONNECTION/INSTALLATION
RM-P2580 System.............................................................................................................12
Procedures ........................................................................................................................14
Mounting the lens ..............................................................................................................15
Installing the ferrite core ....................................................................................................16
Connections on the back ...................................................................................................16
Mounting the camera .........................................................................................................18
Lens adjustment ................................................................................................................20
Back focus adjustment ......................................................................................................21
Auto white balance control adjustment .............................................................................22
AVERTISSEMENT:
POUR EVITER LES RISQUES
D’INCENDIE OU D’ELECTRO-
CUTION, NE PAS EXPOSER
L’APPAREIL A L’HUMIDITE OU A LA
PLUIE.
MENU SETTING
Setting the menu ...............................................................................................................23
The flow of menu screen ...................................................................................................24
SYNC ADJUST Screen .....................................................................................................26
ALC SETTINGS Screen ....................................................................................................26
VIDEO ADJUST Screen ....................................................................................................31
MODE SELECT Screen ....................................................................................................32
MOTION DETECT Screen.................................................................................................34
COMMUNICATION Screen ...............................................................................................35
MAINTENANCE Screen ....................................................................................................35
FACTORY SETTINGS Screen ..........................................................................................35
BLC EDITTING Screen .....................................................................................................36
Manual Adjustment of White Balance ...............................................................................37
CAMERA TITLE Setting ....................................................................................................38
Setting the MOTION DETECT Function ...........................................................................39
Output of Black-White/Colour switching signal .................................................................40
Control by Black-White/Colour switching signal from the outside ....................................41
White spot compensation ..................................................................................................42
OTHERS
Specifications.....................................................................................................................43
E-4
E-5
INTRODUCTION
Features
Operating Precautions
● To save energy, when it is not being used
turn the system’s power off.
● This camera has been designed for indoor
use. When you use it outdoors, be sure
to use a housing or the like.
● Do not install or use the camera in the
following places.
• In a place exposed to rain or moisture.
• In a place with vapor or oil soot, for
example in a kitchen.
• When the ambient temperature rises
above or falls below the acceptable
range (from –10°C to 50°C).
• Near a source of radiation, X-rays,
strong radio waves or magnetism.
• In a place subject to vibration.
● Observe the following when carrying out
camera maintenance.
• Turn the power OFF before proceeding
Ⅲ A DSP (Digital Signal Processor) features
a Extended Dynamic Range (ExDR) and
enables to shoot both bright and dark
locations.
Ⅲ Before starting an important recording,
be sure to perform a test recording in
order to confirm that a normal
recording is possible.
to carry out maintenance.
If it is contaminated seriously, clean the
contaminated part with a cloth (or a
tissue) which has been soaked in a
solution of water and a neutral detergent.
● The unit is to be powered by a DC 12 V
or an AC 24 V power supply. (TK-C1430E)
The AC 24V power supply should conform
to the following: Isolated power supply
only
Ⅲ We do not accept liability for the loss of
a recording in the case of it becoming
impossible to record due to a problem
in the video camera, VCR or video tape.
Ⅲ We do not accept liability for any
damage to the camera in cases where
it is dropped because of bad installation
due to failure to observe the installation
instructions correctly.Please be careful
when installing the camera.
Ⅲ The use of a CCD with a SENSE UP (X32)
function realized the minimum luminous
flux density for subject of 0.9 lx (F1.2,
50%, AGC 20dB) and 0.03 lx (at SENSE
UP (X32)).Furthermore, we realized 0.03
lx (F1.2, 50% AGC 20dB) thanks to the
function of B/W mode.
TK-C1431EG: Connect the power cable to
the commercial power supply of 220V –
240V.
Ⅲ A motion detector function detects the
motion inside an image and emits alarm
signals.
Ⅲ The motion detector is not a feature
which prevents theft, fire, etc. Even if
an accident should occur resulting in
damage, we do not accept any liability.
• In a place with excessive dirt.
● Caution for operating the video iris lens.
If the video iris lens is set to an extremely
low level, a malfunction – such as the
hunting phenomenon where the iris opens
and closes in voluntary – can occur.
In such a case, first set the “LEVEL”
potentiometer on the lens to the H position
(iris open), and then adjust it to an optimum
level. (੬ page 20)
● The cable stopper on the terminal block
can come off sometimes. Therefore, be
sure to take enough time and fix the cable
securely.
● When a highly bright subject is shot,
sometimes undulations can be observed
on the vertical lines of the subject.
However, this phenomenon is peculiar to
the unit and is not a sign of malfunction.
● The beat may sometimes appear on the
screen if gain is raised when the line lock
is in use, but the phenomenon takes place
due to the fluctuation of power frequency
and is not a malfunction.
● You may hear some noise when the
screen is switched between the colour
and the black and white mode, because
the optical filter moves. Also, black vertical
bands will appear on the screen.
● If this camera and the cables connected
to this camera are used where there are
strong electromagnetic waves or where
there is magnetism present, for example
near a radio or TV transmitter, power
transformer or an electric motor, the picture
may produce noise and the colours may
be affected.
● This camera incorporates an AGC circuit.
As a result, when it is used under low light
conditions, the camera sensitivity is
automatically boosted and the picture may
look uneven. However, this is not a
malfunction.
● While the AGC is activated, if transceiver
which causes strong electromagnetic
wave is at close distance, picture might
suffer from beat.
So please use the camera more than three
meters from such transceivers.
● When this camera is used in the ATW
mode, the recorded colours may be slightly
different from the actual colours due to the
operational principles of the auto-tracking
white balance circuit. However, this is not
a malfunction.
● If a high-intensity object (such as a lamp)
is shot, the image on the screen may have
vertical lines (smear) or blur (blooming)
at its periphery.This is a characteristic of
the CCD, and is not a defect.
Ⅲ The equipped Y/C terminals and RS-
422A/RS-485 terminals allow intended
compatibility with diversified systems.
Ⅲ Day/Night surveillance
When the light is low, the camera pictures
can be switched automatically to black
and white pictures.
Ⅲ Electronic zoom
The 10x electronic zoom allows
monitoring in far greater detail.
Characters and symbols used in this instruction manual.
CAUTION : Cautionary notes concerning operation of the unit.
MEMO
: Reference such as restrictions of features, etc.
: Reference page or item.
੬
● Set the Iris Selector switch to VIDEO to
use the manual lens.
E-6
E-7
INTRODUCTION
Controls, Connectors and Indicators
SET
AWC
CAMERA
SETUP
ON
LL
EXT TERM-OFF
INT/GL
MENU
SIMPLEX
DUPLEX
RX TERM-OFF
ON
NOT USED
IRIS
VIDEO
DC
Lens mount
To attach the lens.
This is applicable to both C-mount lenses
and CS-mount lenses.
Camera-mounting bracket
Cover
[SET/AWC] Set. Auto White Control
Button
SET: Press this button to display a sub-
menu.
1
2
4
8
9
12
The bracket has been attached on the
bottom of the camera before shipment. It
can also be attached on the top
according to the circumstance.
To re-attach the bracket use the threaded
holes at the top, with the camera
The cover slides open when push to the
left.
[VIDEO/DC] Iris Selector Switch
This should be set according to the type
of lens if an automatic iris control lens is
used.
VIDEO: In case of lens with EE amp built-
in.
(੬ Page 23)
Back focus adjustment ring
Adjusting the back focus during lens
installation.
AWC: If this button is kept pressed for
more th |