45235
Home Monitoring
B/W Wireless
Camera System
with Monitor
User Manual
1-800-654-8483
3
1. 45235B/W Wireless Camera
2. 45235 5.5” B/W CRT monitor
3. Wall mounting hardware
4. 2 AC adapters
BEFORE YOU INSTALL
When choosing the best location for the placement
of the camera and monitor, it is best to avoid any
sources of possible RF interference such as
microwave ovens and cordless phones. Proximity
to these and other sources of RF interference can
inhibit the proper functioning of the receiver.
The 900MHz video signals pass easily through
your home’s interior walls, but the signal may be
reflected by power wires or plumbing inside those
walls. Usually a slight adjustment to the position
of the Monitor/Receiver and/or Camera antenna
will improve reception. Take care not to force the
antennas past their lock positions.
CHOOSING A CAMERA MOUNTING LOCATION
The Wireless B/W Camera included in the 45235
system can be positioned on a desktop, or
mounted to a wall. It is suitable for indoor or
outdoor use. When choosing a mounting location,
please be advised:
4
• Do not use in wet locations. If using outside,
position camera in a sheltered location.
• Do not position the camera so that it points
directly into the sun or any bright light, as this
may cause damage to the camera.
• Avoid viewing areas where half the area is in
bright sunlight and the other half is dark, such
as in the shadow of a building. All types of
cameras have difficulty “seeing” into areas of
such divergent light levels.
• In low light conditions, the camera will
automatically activate the Infrared (IR) LED’s and
switch the camera to Night Vision mode. Night
Vision viewing distance is up to 10 feet.
• The AC adapter used to power the camera
cannot be positioned farther than 8 ft. from
an AC socket. Do not use the supplied adapter
outside or run the cable through walls. If you
need to extend the adapter cable, 15 ft.
extensions are available by contacting
Customer Service at 800-654-8483.
• The Camera has an unobstructed wireless
transmission range up to 200 ft. from the
receiver. Transmission distance indoors is
reduced due to interior walls, wiring, household
fixtures and metal plumbing.
5
CONNECTING TO THE MONITOR
Before beginning installation, we recommend that
you temporarily “connect” the 45235 B/W Wireless
Camera to the 5.5” Monitor to help familiarize
yourself with the camera system and select the
best location for installing the camera. The camera
connects wirelessly and automatically to the monitor
when both are powered on and within 200 ft. of
each other (unobstructed view). This system will
accommodate up to 2 cameras.
Shown with optional
rechargeable battery
(Sold separately)
1. Plug the AC adapter into the power jack on the
back of the monitor, then into an AC outlet.
2. Turn on the monitor by pressing the power
button on the front of the unit. Adjust the sound
level at the front of the monitor to midpoint with
the volume control knob.
3. Select the appropriate “channel” (1 or 2) on the
monitor that corresponds to the channel switch
6
Channel
Selection
switch
setting (1 or 2) located on
the unside of the camera
housing. (See Channel
Selection.)
1
2
4. Brightness/Contrast and
Vertical Hold can be adjusted
with controls at the back of
the monitor.
Monitor
controls
–
+
–
+
BEEP
TRIGGER
13.5V 1.2A Audio Out
Video Out
1
2
1/2
V-HOLD
BRIGHT
CONT
CHANNEL
Channel
Selection switch
CHANNEL SELECTION
Manual Mode
To select one of the two channels manually,
press the MANUAL button on the front panel
of the Monitor. The green LED will light for the
corresponding channel. The Monitor will switch to
a different channel (1 or 2) each time the MANUAL
button is pressed. When you have selected the
channel with the active camera, that video will
appear on the monitor screen. Each camera must
be assigned to a specific channel; both cameras
cannot be on the same channel or the signals will
cancel out.
7
Multi-Camera Operation
This wireless surveillance system is designed to
work with up to 2 cameras. Additional cameras
are sold separately. IMPORTANT: When using
more than one camera, each camera must be
assigned to a specific channel using the channel
selection switch located on the underside of the
camera housing.
Select either 1 or 2 for each camera. Each camera
must be assigned to a specific channel; both
cameras cannot be on the same channel or the
signals will cancel out. If using only one camera
you can select either Ch 1 or Ch 2, whichever
provides the best picture. The slide switch located
on the rear of the Receiver must be set to reflect
the channels in use.
MONITOR
Channel
Selection
switch
1
2
1
2
–
+
–
+
BEEP
TRIGGER
13.5V 1.2A Audio Out
Video Out
1
2
1/2
V-HOLD
BRIGHT
CONT
CAMERA 1
Channel Setting
CAMERA 2
Channel Setting
CHANNEL
Auto Mode (2 Camera Operation)
To have the Monitor automatically switch between
two active channels, first check the receiver is set
8
to 1/2 position. Next, press the AUTO button on the
front panel of the Monitor. The green LED will light
and the Monitor will automatically select between
the two active cameras. The monitor will display
images from both cameras alternately.
Cycle Time Setting
(Time interval between camera selections)
The default cycle time for the receiver is preset to
4 seconds. To change the cycle time, press both of
the buttons (Auto/Manual) on front of the receiver
simultaneously. The Monitor will beep. Each beep
is one extra second of cycle time added. The cycle
time can be verified by the number of flashes the
LED makes when you release the buttons—one
flash equals one second. Cycle time can be set
between 2-30 seconds.
NIGHT VISION
The 45233 Wireless Color Camera features Night
Vision technology. Objects and images can be seen
in little or no light up to 10 ft. The camera uses a
special image sensor that automatically detects
available light levels. It turns on/off the Infra-Red
(IR) LEDS on the front of the camera. These LEDs
provide artificial light that allows the camera to
‘see’ in the dark. Night Vision will appear as a Black
and White image. When the image sensor detects
9
Infra-Red
(IR) LEDs
enough light, color will
return to the images.
AUDIO DETECTION AND
NOTIFICATION FEATURE
This feature allows the system
to emit an audio alert whenever
sound is detected within a
monitored area. When the
camera detects a sound, the
receiver will sound an alert and
Sensor
‘Alarm’ light on the front of the Monitor will flash. The
sensitivity for the level of audio detection (when the
Monitor will sound an alert) can be adjusted with the
sensitivity control located at the back of the Monitor.
The alert sound can be turned OFF by adjusting the
sensitivity control to ‘-’ (Minimum).
–
+
–
+
Sensitivity
Control
BEEP
TRIGGER
13.5V 1.2A Audio Out
Video Out
(Trigger)
1
2
1/2
V-HOLD
BRIGHT
CONT
CHANNEL
INSTALLATION
Once your preferred camera mounting location
has been chosen, power OFF the Monitor and
disconnect the AC adapter from the wireless
camera before proceeding.
10
Desktop Mount:
1. Place camera in desired
location on a flat surface.
MAX
2. Set Channel switch on
camera to 1 or 2.
MIN
3. Reconnect AC adapter to
the camera and power on the
monitor.
Antenna pivots to
increase/decrease
signal strength
4. Adjust antenna and camera
angle as needed for the clearest
picture. Positioning the antenna
upwards to improve transmission distance, and
downwards to reduce transmission. Take care not
to force the antenna past its lock positions.
Wall Mount:
1. To simplify the wall mount process, you will find
a custom wall mounting plate included with the
mounting hardware.
2. Select the ideal location. Using the supplied mount
as a template, drill two 3/16” holes in the desired
mounting location, and install the two wall anchors
(included) into the holes, or screw directly into a wall
stud. Secure the mounting plate to the wall, Do not
run the adapter cable in walls; when securing the
cable, do not cut or puncture.
11
3. Set Channel
switch on camera
to 1 or 2. Slide the
camera onto the
alignment and
locking pins of
the mounting
plate.
4. Adjust antenna and
camera angle as needed
for the clearest picture.
USING THE 45235 B/W
WIRELESS CAMERA
SYSTEM WITH A
MONITOR
VCR
You can connect the
45235 Monitor to a
VCR, DVR or another
monitor in order to
record/view the images
received from up to 2
cameras. If connected to
–
+
–
+
BEEP
TRIGGER
13.5V 1.2A Audio Out
Video Out
1
2
1/2
V-HOLD
BRIGHT
CONT
CHANNEL
VCR
Video In Audio In
VCR or DVR, the VCR/DVR must also be connected a
TV/Monitor in order to see live or recorded images.
12
AC adapter
charges the
battery
Wall or desktop mount
OPTIONAL WIRELESS BATTERY PACK AVAILABLE
(SOLD SEPARATELY)
Rechargeable NiMH Battery is available for use with
the 45235 Wireless B/W Camera. This 850mAh
battery will power the wireless Camera for
approximately 5 hours on a single charge. To order
this battery, please visit www.jascoproducts.com/
batteryoffer or call our Customer Support
department at 1-800-654-8483, Monday–Friday
8 a.m.–5 p.m. CST.
TROUBLE SHOOTING
If you have any questions or feel the camera
system is not operating correctly, or you simply
need additional information, please visit our web
Customer Service Group 1-800-654-8483.
13
No camera picture
1. Check all connections. Make sure camera(s) and
receiver are powered ON.
2. Ensure camera(s) and receiver are set to correct
channel(s).
3. Make sure camera is within range of receiver.
4. Adjust the antennas of the monitor and camera(s).
Blank monitor
1. Make sure receiver or monitor is switched ON,
and the correct video input has been selected
2. If using AC adapter, make sure it is plugged in.
3. If using a battery, make sure it is installed
correctly, and is fully charged.
Interference on camera picture
1. Make sure each camera (transmitter) is within
range, and that no large obstructions are blocking
the signal.
2. Try repositioning the camera, monitor (receiver) or
both to improve the reception quality.
3. If a camera is positioned close to the monitor,
point antenna away from the monitor.
4. Reposition other nearby equipment transmitting
on the 900MHz frequency.
14
5. Adjust the antennas of the monitor and camera(s).
Audio problems
1. Ensure the volume is turned up sufficiently on the
Monitor (or TV).
2. Make sure the sound is within the microphone
range.
3. If the unit emits a loud wailing sound (feeds back),
try moving the camera away from the monitor or
angle the monitor in a different direction.
SPECIFICATIONS (Subject to change without notice.)
CAMERA
TV System.....................................................................................................NTSC
Integrated Lens...................................................5.6mm, F1.8 fixed focus
Resolution..............................................................360 horizontal TV Lines
High-Speed Electronic Shutter..............................1/60 - 1/6,000 sec
Image Sensor...................................................................................1/4” CMOS
Min. Illumination........................................... 0 lux at 3 ft, 0.5 lux at 10ft
Voltage...........................................................................................................9VDC
Current Consumption..................................................150mA maximum
Overall Size..............................................................2.35”W x2.74Hx3.160D
Frequency Range................................................................... 902 - 928 GHz
Modulation........................................................................................................FM
Channel Selection ...............................................................................Manual
Case Finish...........................................................UV resistant ABS plastic
MONITOR
Frequency Range...................................................................902 - 928 MHz
Voltage....................................................................................................13.5VDC
15
Current Consumption......................................................Approx. 800 mA
Output .............................................................................................Audio/Video
Overall Size.........................................................5.7” W x 7.28” H x 8.46” D
WARRANTY
ONE-YEAR LIMITED WARRANTY: Jasco Products Company
warrants this product to be free from manufacturing defects
for a period of one year from the original date of consumer
purchase. This warranty is limited to the repair or replacement
of this product only and does not extend to consequential or
incidental damage to other products that may be used with
this unit. This warranty is in lieu of all other warranties express
or implied. Some states do not allow limitations on how long an
implied warranty lasts or permit the exclusion or limitation of
incidental or consequential damages, so the above limitations
may not apply to you. This warranty gives you specific rights,
and you may also have other rights which vary from state to
state. If unit should prove defective within the warranty period,
return prepaid with dated proof of purchase to:
Jasco Products Company
10 E. Memorial Road, Oklahoma City, OK 73114
WARNING
Risk of fire and shock
• Only use the supplied cUL listed AC to DC adapter.
• The supplied adapter is for indoor use only.
• Do not run the camera cable inside walls; when securing the
cable, do not cut or puncture
• Do not use in wet locations
16
FCC STATEMENT
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
Made in China
is a trademark of General Electric Company
and is used under license to Jasco Products Company LLC,
10 E. Memorial Road, Oklahoma City, OK 73114
|